DLM1771-DLM1772(Y)-DLM1775(Y) Integrated Camera Positioning w/Optional Dual IR Lamps Installa
STEP 3 Install power supply, video output, RS-485 control input wiring through waterproof connector plugs, and connect them to the correspond
STEP 5 Loosen the screw nut cover on the pan tilt’s left side, to expose the 8 DIP dial switch. Set the protocol, baud rate, addre
DLM177x Pedestal Mount
3.2 WALL INSTALLATION The wall installation camera contains following parts. Inspect each package to make sure all parts are present.
3.2.2 Installation Instructions STEP 1 Install the Φ8mm screws on the wall (refer to the following picture) STEP 2 I
STEP 3 Install power supply, video output, RS-485 control input wiring through the body of the bracket and connect them to the corresponding pow
STEP 5 Loosen the screw nut cover on the pan tilt’s left side, to expose the 8 DIP switch. Set the protocol, baud rate, address for the pan
4. TECHNICAL PARAMETERS 4.1 Structure parameters: Integrated pan tilt Aluminum alloy Rotating platform Alumin
Installation dimensions (no IR Lamps): Installation dimensions with LED IR Lamps Installation dimensions with Laser IR Lamps
4.2 Rotating parameters: Pan rotation 360ºcontinuous rotation Tilt rotation +35º ~ -85
Table of Contents DLM1771-DLM1772_DLM1775 and DLM1772Y-DLM1
4.4 Camera, lens parameters Camera Specifications DLM1771 - 18X Day/Night Image Sensor 1/3” Hi
4.5 IR Lamp Parameters Method of operation 1: 1. Enter into menu by pressing preset 95 2. Enter INFRARED in the AUX menu. ON
5. OPERATIONS 5.1 BASIC DESCRIPTIONS After connecting wires as per instructions in previous section and turning on power, the pan tilt camera will
NOTE: 1. VERSION 1.8 is the software version number of the P/T camera, and it will change as the product’s upgrade. 2. PROTOCOL is PTZ
5.3 Preset Functions The following stipulations are for presetting, 5.4 Screen Character Display The speed d
5.5 PTZ FUNCTIONS This series high-speed P/T camera manual pan speed 0.1 º -100 º/second, manual tilt speed 0.1º ~ 80º/second. Pan/
5.6.9 Low lux (color / black & white) function The camera automatically changes CCD lux according to surrounding light. Color image changes to
6. MENU OPERATION This series camera has in-built menu to setup to camera and lens’ parameter. In this chapter, you will get a wh
6.2 MAIN NENU 〈SYSTEM INFORMATION〉 〈CAMERA 〉 〈PAN/TITL 〉 〈POWER UP〉
NOTE: The function of stabilizer and WDR will depends on the module function, if the function shows in the menu; it means the function is available.
1. INSTALLATION MANUAL 1.1 FOREWORD This manual introduces the function, installation and operation of the integrated high speed pan tilt camera
SHUTTER MODE Default Setting: AUTO Shutter Mode: AUTO and MAN SHUTTER SPEED
PARK TIME Default Setting: 30minutes Park Time: 2~60 min selectable PRESET TOUR TIME
6.8 PRIVACY ZONE MENU Note: only the items with privacy function may enter this menu. SONY series module: PRIVACY NO SET DISPLAY
When it is ON, and it is in the status of non-menu, the all privacy zone will be open when setting 64 preset; and closed when using 64 preset. This k
6.9 ALARM INPUT ALARM 1 ALARM 2 BACK ALARM 1(ALARM INPUT 1)
EXIT OSD MENU, then use PRESET 65. The Pan/Tilt will first rotate to the preset 65 position. The preset 65 function is to first position
7. DIP SWITCH SETTING 7.1 Pan/tilt Controls Note: When one control bus controls several (more than 2) Pan/Tilt cameras, it needs a 120ohm resistance
7.3 Switch setting for SW2 Note: Switch SW2 is used to set receiving address. Protocol P addresses setting: Switch setting Address SW2-1 SW2-2
Protocols D address setting: Switch setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF O
Appendix A TROUBLESHOOTING 1. Image Problem: No image displayed on monitor? →First check if the power supply wire connection, voltage, indic
1.3 SAFEGUARD AND WARNINGS Prior to installation and use of this product, please note the following WARNING. This product may be only used in specifi
→DVR control protocol is not compatible with the product or the function is not complete. Problem: why does the same pan tilt
1.3.2 FUNCTION DESCRIPTIONS Screen menu function (OSD) It has screen menu function. All information of camera and pan& tilt may be displayed by
image changes to black& white one in low LUX; black & white image changes to color one in high LUX (related to camera) Auto focus The camera
2.2. PREPARATION FOR INSTALLATION 1) All electric working must be accorded to latest electric, fire proof and related
3.1 PEDESTAL INSTALLATION The pedestal installation camera includes the following parts. Inspect each package to make sure all parts are
3.1.2 INSTALLATION INSTRUCTIONS STEP 1 Locate the floor or impending base level tha
Comments to this Manuals